A backsplash protects the wall behind the counter from water, grease and food, and it does most of the visual work in a kitchen. It is also a smaller tile job than a floor or a shower, which makes it tempting to treat as simple. The tile itself rarely goes wrong. What goes wrong is the planning: where the pattern starts, where it stops, how it meets the counter and how it handles the outlets.
Choosing the material
A backsplash does not take foot traffic, so wall tiles that would be wrong on a floor are fine here.
- Ceramic. Softer and more porous than porcelain, which matters on a floor but not on a wall. It is the classic backsplash tile, easy to cut and available in every shape, from subway tile to handmade-look glazes.
- Porcelain. Denser and harder, and available in large formats and stone or concrete looks. Large-format porcelain means fewer grout lines to clean behind the range.
- Glass. Reflective and easy to wipe clean. It needs a white thinset suited to glass, because the adhesive shows through, and clean cuts take more care than ceramic.
- Natural stone. Marble, travertine and slate look unlike anything else, but stone is porous and some types etch from acidic splashes such as lemon juice, vinegar and tomato. It needs sealing at installation and resealing over time.
- Mosaics. Small tiles mounted on mesh sheets. They suit curves and accent areas, and mean many more grout lines.
Porcelain and ceramic are compared in more depth in tile and stone in the Coulee Region.
How high the tile goes
The standard backsplash runs from the countertop to the underside of the upper cabinets. The decisions come where there are no uppers:
- Behind the range. Tile often runs up to the hood, which protects the wall where splashes are worst and turns the range wall into a feature.
- Around a window. Tile can return into the window opening or stop neatly at the casing, but it should be one or the other, decided in advance.
- Open walls with shelving or no uppers. Tile can stop at a consistent height or run to the ceiling. A short backsplash on an open wall can look unfinished, so it is worth sketching.
Where the backsplash stops
The ends of the backsplash are where it looks either planned or improvised. Where possible, tile stops at a natural line such as the end of the countertop, the outside edge of the upper cabinets or a wall corner. When the edge of the tile is exposed, it needs a finished edge, either a bullnose tile or a metal or PVC edge profile, rather than the raw cut edge of a tile.
Centering the layout
Before any tile is set, the layout is planned on the wall. The pattern is usually centered on the focal point, typically the range or the sink, so that the tiles either side are equal. The goal is to avoid thin slivers of tile at the visible ends and around windows, which are what make a backsplash look cheap. It is also why a dry layout comes first, especially with large tiles or patterns such as herringbone, where the starting line decides everything after it.
Patterned tile follows the same layout rules on a wall as on a floor. Herringbone vs. chevron explains centering and scale.
Where tile meets the countertop
The joint between the backsplash and the countertop, and the inside corners where two walls meet, are changes of plane. Different surfaces move slightly differently there, and grout in those joints cracks. Those joints are filled with a flexible sealant, color-matched to the grout, instead. It is a detail you will not notice when it is done right and will notice within a year when it is not.
Grout
Narrow grout joints, typical with subway tile and glass, take a fine grout made for tight joints; wider joints need a sanded grout to resist shrinkage. Grout color makes a bigger design difference than people expect. Grout close to the tile color makes the wall read as one surface; contrasting grout outlines every tile and makes the pattern the feature. Light grout behind a range shows staining sooner, which is worth knowing before choosing.
Cleaning and sealing grout after installation is covered in tile and grout care.
Outlets and switches
Tile adds thickness to the wall, so outlets and switches on the backsplash end up recessed behind it. Box extenders bring them forward to sit flush with the tile, and the tile is cut neatly around each box. Any electrical work, including moving or adding outlets, is done by a licensed electrician. Outlet placement is worth deciding early, because an outlet in the middle of a feature tile is hard to fix after the tile is up.
Order of work
The backsplash goes in after the countertops are installed, because the tile sits on the finished counter and is laid out from it. That also means it is near the end of a kitchen project: cabinets, then countertops, then backsplash. Replacing an existing backsplash usually damages the drywall behind it when the old tile comes off, so the wall surface is repaired and flattened before the new tile goes up.
The wider kitchen sequence, including where the floor fits, is covered in kitchen remodel flooring: under the cabinets or around them? Choosing the counter itself is covered in kitchen countertops compared.
Planning your backsplash
We install backsplashes in ceramic, porcelain, glass and natural stone, as a standalone job or as part of a kitchen. Our tile and stone page covers the tile work we do, and our room remodels page covers full kitchens. Every installation carries our lifetime workmanship warranty and a free 30-day grout touch-up on any joint that needs it. Book a free in-home estimate and we will plan the layout with you before any tile is ordered.