A tiled shower is the hardest-working surface in the house. It is soaked several times a day, heated and cooled with every shower, and in a Wisconsin winter it sits in a room full of humidity. Built right, it lasts for decades. Built wrong, it can look perfect for years while water quietly reaches the framing behind it.
The difference is almost entirely in what is behind the tile, which is why it is worth understanding before choosing anything you can see.
Tile and grout are not waterproof
Porcelain tile itself sheds water, but grout is porous, and every grout line is a path for water. Cement board, the usual backer behind tile, is not waterproof either: it survives getting wet without falling apart, but water passes through it. A shower depends on a waterproof layer behind the tile that sends the water that gets through to the drain.
Two ways to waterproof a shower
- The older method puts a plastic sheet behind the wall board and a waterproof liner under a sloped mortar bed on the floor. Water soaks through the tile and mortar and is stopped behind them. It works when built carefully, but the mortar bed stays damp, and the liner is easy to puncture or detail badly at the corners and curb.
- The modern method puts a waterproof membrane directly behind the tile, on the surface of the walls and floor, so water stops just behind the tile and grout instead of soaking into the layers beneath. Sheet membranes and liquid-applied membranes both work this way.
The two should not be mixed. A plastic sheet behind the board combined with a surface membrane in front of it traps moisture between them.
Every shower we build uses the full Schluter KERDI system: waterproof foam board panels on the walls, waterproof tape at every seam, sealing bands at the corners, and the KERDI-DRAIN that the membrane bonds to, so the walls, floor and drain work as one sealed system. Showers usually fail at the details, which is why the corners, the curb, the niche and every pipe that comes through the wall are sealed with pieces made for them.
Slope to the drain
A shower floor has to slope continuously to the drain, with no flat spots where water sits. A quarter inch of fall per foot is the common minimum. The slope is built into the base under the tile, not made up in the thickness of the thinset, and the waterproofing follows it so water that reaches the membrane drains too.
Center drain or linear drain
- A center drain needs the floor to slope down from all four sides, like a shallow funnel. That works best with small tiles or mosaic, which follow the changes of slope. Large tiles on a four-way slope tend to leave edges standing proud.
- A linear drain is a long, narrow channel, usually set along the back wall or at the entry. The floor slopes in one direction toward it, as a single flat plane, which allows large-format tile on the shower floor and suits curbless showers.
Smaller floor tiles also mean more grout lines, which gives more grip underfoot. Whatever the tile, it should be suitable for a wet floor.
Curb or curbless
Most showers have a curb, a low raised step at the entry that keeps water in. A curbless shower has the bathroom floor run straight in, which looks open and is easier to use for anyone who has trouble stepping over a curb. The shower floor still needs its slope, so to avoid a step, the floor inside the shower has to start lower than the floor outside it. Whether that is possible depends on the framing under the bathroom, so it is checked at the estimate before the design is settled. Curbless showers also need the drain and any glass placed to keep water from reaching the rest of the floor.
Niches and benches
A recessed niche for bottles is one of the most requested shower features. It is built as part of the waterproofing, with the membrane wrapped into it and its bottom shelf sloped slightly so water runs out instead of sitting. Placement needs thought in a Wisconsin house: a niche set into an exterior wall replaces insulation with a cold pocket, so where possible it goes on an interior wall. Lining the niche up with the tile layout, so grout lines meet its edges cleanly, is planned before any tile is set.
Benches, whether built in or floating, are waterproofed the same way and given a slight fall so they drain.
Sealant at the corners, grout in the field
Inside corners, the joint where the walls meet the floor or the tub, and anywhere tile meets glass or a different material are changes of plane that move slightly as the house and the water temperature change. Grout in those joints cracks. They are finished with a flexible sealant, color-matched to the grout, and the sealant is a maintenance item that is cut out and replaced when it wears.
Ordinary cement grout should be sealed and looked after. Higher-performance and epoxy grouts resist staining better and need less maintenance, at a higher cost and with more care during installation.
Cleaning, sealing and regrouting are covered in tile and grout care.
Testing before the tile goes on
The waterproofing can only be checked before it is covered. A common practice is to flood test the shower floor: the drain is plugged, the base is filled with water and left, and the level is checked for any drop before tile goes on. It is worth asking any contractor whether and how the waterproofing will be tested.
Plumbing, glass and ventilation
The shower valve, the drain connection and any change to the plumbing are done by a licensed plumber, and they are set before the waterproofing so the membrane is sealed around them. Converting a tub to a walk-in shower usually means at least moving the drain. Glass is measured after the tile is finished, because it has to fit the finished walls, so it is one of the last things to arrive.
A fan sized for the room and ducted outside protects the grout, the sealant and the ceiling. In a Wisconsin winter, a bathroom without one holds on to its humidity, and the shower is the first place that shows it.
Signs an old shower is failing
- Grout that keeps cracking, or tiles that sound hollow or move when pressed.
- Mold that comes back in the same place, especially at the bottom of the walls.
- Stains on the ceiling below the bathroom, or a soft floor beside the shower.
- Caulk at the base that keeps failing over damp or dark material.
Regrouting and recaulking fix worn grout and sealant. They do not fix failed waterproofing behind the tile. When water has been getting past the tile for a long time, the honest answer is usually to take the shower back to the studs, repair what the water has damaged and build it again properly.
Time, and living without the shower
Waterproofing, thinset and grout each need time to cure before the next stage, and the shower cannot be used until everything has cured. That time cannot be compressed, so a tiled shower takes longer than the labor alone suggests. If it is the only shower in the house, that is worth planning around before demolition day.
Where a shower sits in the order of a full bathroom remodel is covered in bathroom remodel: the order of work, and a heated floor outside the shower is covered in heated tile floors.
Planning a shower
Shower walls, tub surrounds and walk-in showers are part of our tile and stone work and our room remodels, with plumbing carried out by licensed trades we bring in. Every shower gets the full KERDI waterproofing system, and every project carries our lifetime workmanship warranty. Book a free in-home estimate and we will look at the bathroom, the framing and the layout with you.